USES
|
METHODS
|
ADVANTAGES
|
HAND WIPING MACHINER Y*
|
Dilute 3 ozs. of QUADRA-KLEAN in a gallon of hot or cold water. Hand wipe or spray on. Wipe off.
|
Superior cleaning power for pennies per gallon. Solution won't sour if left on for a long period of time.
|
NEWSPAPE R BUILDING MAINTENA NCE*
|
Mix 2 ozs. of QUADRA-KLEAN to a gallon of clear water.
|
Readily emulsifies "ink mist." Effectively cleans walls and floors. Fast, economical.
|
STEAM CLEANING
|
Mix 1 part QUADRA-KLEAN to 25 or more parts of cold water. Concentration depends on stubbornness of soiled area. Add more QUADRA-KLEAN as needed.
|
Safe on most types of metal. Provides speedy wetting and penetrating action.
|
MAINTENA NCE OF FLOORS, WALLS, BLACKBOA RDS AND PAINTED SURFACES*
|
Dilute 1 oz. QUADRA-KLEAN to a gallon of clear, clean water (hot or cold). For stripping most floor finishes, mix at a ratio of 1 part QUADRA-KLEAN to 5 parts water. Let solution set 10 minutes, but do not let it dry. Agitate with stiff bristle brush or broom. Mop floor, then rinse with clean water and allow floor to dry.
|
Superior cleaning at less than eight cents per gallon.
|
CAR WASHING*
|
Pre-rinse by hosing down with plain water. Dilute 1 oz. of QUADRA-KLEAN to a gallon of clear water. Use brush or swab. Hose rinse with clear water.
|
No harm to expensive car finish. Leaves bright, well-kept appearance. Virtually free rinsing.
|
CONCRETE FLOORS WITH HEAVY DEPOSITS OF OIL AND GREASE (Driveways, Runways, Loading Docks)
|
Mix 1 part QUADRA-KLEAN to 5 parts solvent.** (NOTE: Mix 1 gallon of solvent and 1 gallon of QUADRA-KLEAN thoroughly. Then add remaining 4 gallons of solvent.) Let soak. Agitate when necessary. Rinse with high pressure hose. One gallon of solution covers approximately 150 sq. ft.
|
Strong wetting, penetrating and emulsifying action. Excellent rinsibility and water hardness control. (When drain facilities are not available, remove excess solution with rubber-bladed squeegee. Area may be mopped with clear rinse water.)
|
HEAVY DUTY EQUIPMEN T WASHING
|
Pre-rinse equipment to be cleaned. Add 1 to 3 ozs. of QUADRA-KLEAN to each gallon of water, depending upon soiled condition of equipment. Use cold or warm water. Apply mixture of QUADRA-KLEAN and water to equipment. Agitate extremely soiled areas with a brush or swab. Let solution soak for 5 to 10 minutes. Then rinse equipment clean.
|
No harm to most painted surfaces. Dirt rinses away easily. An economical, effective cleaner
|
CLEANING AND DEGREASI NG INDUSTRIA L EQUIPMEN T (Pumps, engines, compressors)
TRUCK AND CAR MOTORS
|
Dilute 1 part QUADRA-KLEAN to 5 parts solvent.** (NOTE: Mix 1 gallon of solvent and 1 gallon of QUADRA-KLEAN thoroughly. Then add remaining 4 gallons of solvent.) Spray or brush solution over entire surface. Let soak for 5 to 15 minutes. Rinse surface with water hose and use air hose, if one is available, to blow off excess water. This solution is COMBUSTIBLE.
|
Light Solvent odor. Safe on most metal parts. Unequaled wetting and penetrating action. Controls lime and scale deposits. Let very hot surfaces (exhaust system) cool down before application - works extremely well on warm motor surfaces. While cleaning is in process, do not operate equipment. Equipment is ready to use immediately after cleaning.
|