Texas Refinery Coatings

CONCRETE MAGI-PATCH

(One Component Quick-Setting Cement)

UCONCRETE MAGI-PATCH is a one component cement that sets up ready for traffic in less than one hour. Almost three times stronger than concrete, it can be used to repair all types of concrete structures: steps, walkways, fence posts, loading docks, and many other areas.SER BENEFITS:

  • QUICK SET-UP
  • EXTRA STRONG - WILL NOT SHRINK
  • MULTIPLE USES
  • EASY TO APPLY

CONCRETE MAGI-PATCH is a one component cement that sets up ready for traffic in less than one hour. Almost three times stronger than concrete, it can be used to repair all types of concrete structures: steps, walkways, fence posts, loading docks, and many other areas.

CONCRETE MAGI-PATCH

Quick Set-Up

CONCRETE MAGI-PATCH sets up in just twenty minutes and is ready for traffic in only one hour. Rapid set-up eliminates costly down time - - helps workers get back on the job quickly.

CONCRETE MAGI-PATCH

Extra Strong - Will Not Shrink

CONCRETE MAGI-PATCH is remarkably strong. It develops compressive strengths up to 10,000 psi. It will not shrink. It is resistant to freeze/thaw cycles and de-icing chemicals.

CONCRETE MAGI-PATCH

Multiple Uses

CONCRETE MAGI-PATCH may be used to repair above or below grade concrete. Can be used almost anywhere concrete occurs. Application can be made easily and quickly, producing a bond stronger than the surrounding concrete. It is excellent for use in repairing:

 

Loading Docks

Concrete Steps

 

Concrete Chuck Holes

Parking Decks

Installation of Bolts in Concrete Floors

Bridge Railings

Concrete Curbs

Freezer Rooms

Fence Posts

Metal Railings

CONCRETE MAGI-PATCH

Easy To Apply

CONCRETE MAGI-PATCH is easy to apply. After thoroughly mixing with water, pour the material into the hole to be repaired and level the patch with the surrounding concrete.

Use a mortar-type mixer for large jobs. For smaller jobs, an electric drill with an attachment or a simple shovel is adequate.

CONCRETE MAGI-PATCH

Application

SURFACE PREPARATION: Clean surface for repair, removing loose debris, disintegrated concrete, oil, grease and dirt. Flush the area thoroughly with clean water and allow to dry. A dry surface ensures a better bond.

MIXING: At room temperature, the mixing and pouring procedure should take no longer than 10 minutes as its initial set time is 10 to 15 minutes. The warmer the ambient temperature and temperature of the surface to be repaired, the faster the cure time. Cold temperatures slow down the cure time. In very cold temperatures, it may be necessary to warm the surface before filling.

To mix, add ? gallon of water to 50 pounds of CONCRETE MAGI-PATCH. Mix for one minute, making sure that all the dry powder is wetted and stirred thoroughly.

Caution should be taken when handling the mixture at this point - it becomes very hot! After thorough mixing, pour the material into the hole, working it in to assure a good bond. Next, screed off the patch and level it with the surrounding concrete.

COVERAGE: One 50 pound container of CONCRETE MAGI-PATCH mixed with ? gallon of water will cover 10 square feet, ? inch thick.

NOTE: For deep patches, add extra aggregate during the mixing procedure at a rate of up to 30 pounds per 50 pounds of CONCRETE MAGI-PATCH.

CLEAN UP: As soon as possible, clean tools with clean water before the mixing sets up. Set up time is 10 - 15 minutes.

 

CONCRETE MAGI-PATCH

PRODUCT CODE #3120

PHYSICAL PROPERTIES:

Color

Gray

 

Form

Dry Powder

Flow

Good

Weight/Volume

109 lbs./ft.3

VICAT SET - Minutes
(ASTM C 191)

Beginning
Initial
Final

15
16.5
18

Ultimate Temperature, ?F.

170

Compressive Strengths (psi)

1 hour
2 hours
3 hours

6017
7657
8532

MIX RATIOS:

WATER
gallon
1 quart
1 pint

CEMENT
50 pounds
25 pounds
12.5 pounds